Engineers compare FR4 vs 3240 epoxy constantly, and for good reason: both materials look similar on a spec sheet, yet they behave very differently once heat, humidity, and machining enter the picture. Choose the wrong laminate for an insulation fixture, and the mistake usually shows up only after a few thousand duty cycles — once a bracket that looked fine on paper starts absorbing moisture or losing dielectric strength under load.
Quick answer: In the FR4 vs 3240 epoxy comparison, FR4 wins on strength, heat resistance, and flame safety, so most engineers specify it for high-voltage or high-temperature fixtures. 3240 epoxy, however, costs less and machines more easily, which makes it the practical choice for low- to medium-voltage, indoor, general-purpose parts. The sections below explain why, then a comparison table sums up the trade-offs.

What Is FR4?
FR4 is a glass-fiber-reinforced epoxy laminate. Manufacturers build it from woven E-glass cloth, impregnate the cloth with bisphenol-A epoxy resin, and then cure the stack under heat and pressure along with flame-retardant additives. The “FR” stands for flame retardant, and the “4” places it within the NEMA LI 1 industrial laminate grading system. Because of that additive package, FR4 laminates pass the UL 94 V-0 flammability standard, meaning a test flame self-extinguishes within seconds instead of spreading.
That combination of glass reinforcement and a flame-retardant epoxy matrix explains why FR4 became the standard substrate for printed circuit boards. As a result, it’s also the default material whenever an insulation fixture needs to survive heat, load, and moisture at the same time.
FR4 Key Material Properties
| Property | Typical Value |
|---|---|
| Glass transition temperature (Tg) | 130°C–150°C (high-Tg grades run higher) |
| Flammability rating | UL 94 V-0 |
| Water absorption | Low — under 0.25% per ASTM D570 in most grades |
| Dielectric strength | Approximately 20–25 kV/mm |
| Flexural strength | Approximately 415 MPa (typical NEMA G-10/FR-4 data) |
| Machining | Abrasive — wears tooling faster than 3240 |
Where Fabricators Use FR4
- PCB substrates and precision electrical insulators
- Transformer and motor winding insulation
- High-voltage standoffs and busbar supports
- Structural brackets that also need a high strength-to-weight ratio
- Aerospace and defense components, where the flame rating is non-negotiable
What Is 3240 Epoxy?
3240 epoxy, designated EPGC201 under IEC 60893-3-2 and China’s GB/T 1303.4-2009 standard, is a laminate made from alkali-free electrical glass cloth impregnated with an epoxy-phenolic resin blend, then dried and hot-pressed into sheet stock. Unlike FR4, it isn’t a pure epoxy system; the phenolic content keeps material cost down while still delivering solid mechanical and dielectric performance.
The material carries a Class B thermal rating, which under IEC and NEMA thermal classification tops out at 130°C. This point is worth flagging, since several supplier listings online misquote the number as 155°C — that figure actually belongs to Class F, not Class B. Standard 3240 sheet runs 0.5 mm to 50 mm thick, and fabricators can special-order heavier stock up to 150 mm, in yellow, red, green, or black. Curing shrinkage stays under 2%, and properly finished sheets come out flat, bubble-free, and cleanly edged.

3240 Epoxy Key Properties
- Solid mechanical strength at room and moderate temperature
- Reliable electrical insulation for low- and medium-voltage work
- Excellent machinability — the main reason fabricators specify it for tooling and jigs
- Continuous service temperature around 120°C
- Lower material cost than FR4
- Good balance of toughness and rigidity
Where Fabricators Use 3240 Epoxy
- Switchboards and control panel insulation
- Low- and medium-voltage insulation fixtures
- Structural insulation brackets and supports
- CNC tooling jigs and fixtures
- General industrial insulating parts
FR4 vs 3240 Epoxy: Side-by-Side Comparison
| Property | FR4 | 3240 Epoxy |
|---|---|---|
| Mechanical strength | Higher — holds up better under sustained load | Good, though it softens more under load than FR4 |
| Electrical insulation | Better dielectric stability, especially in humidity | Adequate for low- and medium-voltage duty |
| Heat resistance | 130°C–150°C (Tg) | Approximately 120°C continuous; 130°C Class B rating |
| Flame retardancy | UL 94 V-0 | Not flame-retardant in the standard grade |
| Moisture absorption | Low | Higher — performance drops in damp environments |
| Machinability | Abrasive; wears tooling | Easy to cut, drill, and mill |
| Relative cost | Higher | Lower |
| Best fit | High-performance, high-voltage, high-heat fixtures | Cost-sensitive, general-purpose, easy-machining fixtures |
In short, FR4’s glass-epoxy matrix and flame-retardant additives cost more to produce, but that investment buys real headroom in strength, heat tolerance, and dielectric stability. 3240’s epoxy-phenolic system trades some of that headroom for a lower price per sheet and noticeably easier machining.
FR4 vs 3240 Epoxy: Which One Should You Choose?
Choose FR4 when the fixture will face:
- Continuous operating temperatures above 120°C
- High-voltage circuits or strict dielectric-stability requirements
- Damp, humid, or outdoor conditions
- A mandatory flame-retardant rating (UL 94 V-0)
- Heavy mechanical loading over the fixture’s service life
Choose 3240 epoxy when the fixture involves:
- Indoor, low- to medium-voltage insulation
- A tight budget or a high-volume production run
- Extensive machining, drilling, or CNC tooling work
- Moderate heat exposure (under approximately 120°C) with no flame-rating requirement
FAQs About FR4 vs 3240 Epoxy
Is 3240 epoxy the same as FR4? No, and this is the most common point of confusion in the FR4 vs 3240 epoxy debate. FR4 uses a flame-retardant bisphenol-A epoxy resin and meets UL 94 V-0, while 3240 (EPGC201) uses an epoxy-phenolic resin blend and is not flame-retardant in its standard form.
What temperature can 3240 epoxy handle? 3240 carries a Class B thermal rating, which caps continuous service at 130°C. That said, most suppliers list a practical continuous-use temperature closer to 120°C.
Why is FR4 harder to machine than 3240? FR4’s glass fiber content and harder resin system make it more abrasive, so it wears down cutting tools faster. 3240’s epoxy-phenolic matrix cuts and drills more cleanly, which is why fabricators generally prefer it for tooling jigs and fixtures.
Can 3240 epoxy be used outdoors or in humid environments? Not ideally. 3240 absorbs more moisture than FR4, and its dielectric performance degrades under sustained humidity. FR4 or a higher-grade laminate like G11 is the safer pick for damp or outdoor installations.
Which material costs less? 3240 epoxy is the more economical option per sheet. FR4 costs more up front, but it typically justifies the premium in applications where a strength, heat-resistance, or flame-safety failure would be costly.
Bottom Line: FR4 vs 3240 Epoxy
If your fixture must survive high voltage, sustained heat above 130°C, flame exposure, or a damp environment, then FR4 is the right call, since it’s built for that margin of safety. On the other hand, if you’re machining low- to medium-voltage insulation parts on a budget and don’t need a flame rating, 3240 epoxy gets the job done for less. Either way, matching the material to the actual operating conditions — not just the price tag — is what keeps an insulation fixture from failing early.
Need help specifying the right grade or thickness for your application? Get a quote, and our team will match the material to your spec.


